Operation (continued)
Turn power switch on: Following initial power on of the LAN CABLE TESTER, the unit will display the startup logo with back light for 3 seconds,
then will display the top menu for “cable test”.
LAN CABLE TESTER startup menu
C T C U N I O N
L C T . . v 1 . 0
LAN CABLE TESTER test menu
ODE SEL:
cable tes t
Battery
Low
Icon
∗ Press “ENTER” to test the cable.
o 1 2 3 4 5 6 7 8 G
i 3 6 1 4 5 2 7 8
Type
Results Displayed
100BASE/ H U B
UTP i d : 1
Use MODE/SEL to toggle between cable pin out screen and result display, press ESC back to test menu.
Cable testing: During any mode of cable testing, the first screen display will show the top line out and bottom line in of connections 1 through 8 plus G
(shield) as they are scanned. Following this screen page will be the cable identification information. If at least one wire pair is not connected, the display
will read “NO CONNECT”. A shorted cable will read “SHORT”. A question mark in the pin out display indicates a short. An unknown is not in the
standard known pin outs or in the user defined memory.
User Defined cable: The User Define function allows you to describe your own custom cable pin out which will be entered into the cable identification
database and saved in the CPU memory. This custom pin out will remain available as long as a fresh battery is in the unit. Two methods are available for
defining a cable. The first method is manual entry, while the second uses an "UNKNOWN" cable as the pin out source. First the manual method. From
the very top of the LAN CABLE TESTER menu (just after power on is completed) select the USER DEF menu by pressing the MODE/SEL button (step
no. 1 to 2). The MODE/SEL button will now move the cursor to select one of four (4) user memory locations (step no. 3). Press ENTER to select the
memory location that the cursor is on. The define cable display will show (step no. 4).
LAN CABLE TESTER test menu
O D E S E L :
c a b l e t e s t
LAN CABLE TESTER user defined menu
O D E S E L :
u s e r d e f i n e d
LAN CABLE TESTER User Def display (4 locations)
U S E R D E F .
# 1 / 2 / 3 / 4
LAN CABLE TESTER Define cable display
o 1 2 3 4 5 6 7 8 G
i
Use the ENTER key to set digits 1 to 8, G or blank (not connected), then press MODE/SEL to move to the next space.
When completed, press ESC.(step no. 5 to 6)
LAN CABLE TESTER defined pin out
o 1 2 3 4 5 6 7 8 G
i 3 4 1 2 6 5 7 8
LAN CABLE TESTER Save to User Defined
Confirmation display
S A V E T O U S E R
D E F . # 2 ?
To save your definition, ∗ press ENTER. To exit without saving, ∗ press ESC. The alternate method is to save the "Unknown" type.
U N K N O
N D E F .
U T P i d : 1
SAVE TO USER
DEF. ?
U S E R D E F .
# 1 / 2 / 3 / 4
Select the location with MODE/SEL and then press ENTER to save. Press ESC anytime to exit.
Cable Fault Indication Examples:
O D E S E L :
c a b l e t e s t
o 12345678G
i 11345678
C A B L E S H O R T
i d:1
In the above example, Pin 1 and Pin 2 were found to be shorted.
O D E S E L :
c a b l e t e s t
o 12345678G
i
N O C O N N E C T
In the second example, if at least one pair of wires is not connected, the test result will show as "NO CONNECT".
41RP-170300-000
empty
Pin Out
Terminator
ID No.
UTP, FTP or COAX
MODE/SEL
ENTER
MODE/SEL
to location 1~4 then ENTER
defined
pin out
ES
ENTER
MODE/SEL
ESC out
∗ ENTER
∗ ENTER
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels